Sikorsky (SAC) Switches to DTi Spring-Fast® Grommet Edging for the Blackhawk UH-60M
Southborough, MA February 13, 2019 – Device Technologies (DTi), a leading manufacturer of wire protection products, is pleased to announce that Sikorsky Aircraft Corporation (SAC), a division of Lockheed Martin, has executed an Engineering Change (EC) to use DTi’s Spring-Fast® M22529/2 grommet edging in place of the legacy MS21266 nylon grommets for select applications on the Blackhawk UH-60M.
Sikorsky Turns to Wire Protection Experts
SAC turned to DTi for a solution because DTi’s Spring-Fast provides best-in-class EWIS anti-chafe, arcing and sparking protection but at half the cost of legacy systems due to its fast finger pressure install with no glue, no clean up and no curing.
Sikorsky made the change after careful evaluation because critical machined fittings that are used to secure the Active Vibration System were being subjected to vibration of between 10 and 25 Hz. This was causing repeated, non-conforming, discrepancy reports as the legacy glued nylon grommets were dis-bonding and pulling away from the edges and surfaces to which they were applied.
Further compounding the problem were tight radii and reverse curves that made up the periphery of the machine fitting. Without protective edge grommets wiring was susceptible to chafing which created the discrepancy reports and over time it could lead to potentially catastrophic sparking and arcing.
Nick Petri, Managing Director of DTi indicated, “The Blackhawk is another success for DTi. We have supplied our Mil Spec quality grommets for numerous tactical aircraft like the V280 Velour, CH-47 Chinook, C-17 Globemaster, T38 trainer and many others.” He continued “It takes time for OEM systems and thinking to change, but we know we have a better alternative than legacy systems, and our job is to show OEM’s the performance and cost benefits.”
The problem with the old MS21266 legacy grommet is that it lacked the flexibility and static friction needed to hold to varying radii. Despite the adhesive and heat being applied to soften and make the nylon more malleable during application, it retained its tendency to dis-bond. This created discrepancies as well as a high cost-of-poor-quality as installation work had to be rigorously checked and often reworked.
In contrast, the M22529/2 has superior retentive capabilities; its thin CRES substrate allows technicians to hand pre-form the grommet to rough interfaces and shapes and then easily snap them into place with just finger pressure. The M22529/2 has been static load tested to 20G on all three axes without adhesives.
“We are proud of this Blackhawk EC but this has implications far wider than aerospace as Spring-Fast grommet edging achieves a rare feat –it provides best-in-class performance for half the cost,” said Nick Petri. “Any OEM in any industry who uses the old nylon grommet edging with glue can take advantage of this best-in-class performance for half of the installed cost.”
About Device Technologies, Inc.
Founded in 1984, Device Technologies, Inc. (DTi) designs, manufactures and sells specialty components including grommet edgings, enclosure seals, trims, and wire protection sleeving and EMI shielding/absorber/thermal materials for a broad spectrum of uses including aerospace and avionics OEM and MRO applications, Tactical Equipment, Wind Turbines, Telecom back up power systems, and IT Servers. DTi’s advanced protection materials have wide applications in other industries such as HVAC, Transportation, Medical, Military, Gaming, Automotive and Food Service Manufacturing.
DTi’s Advanced Technology Division (ATD) specializes in fully automated, linear and selective polymer coating for cable, wire, flat wire, stampings and profile metal-formed products encapsulated in a broad range of thermo-plastic and thermo-setting resins.
DTi continues to invest in R&D to enhance opportunities for its product and process technologies, in compliance with ISO 9001 and AS9100 standards. More information is available at www.devicetech.com or call (508)-229-2000.
Spring Fast®, Fast-Drop®, Trim-Fast™, Seal-Fast™, Protect-Fast™ and Shield-Fast™ are registered trademarks of Device Technologies, Inc.
Customer Service Contact:
Device Technologies, Inc.
155 Northboro Rd., Unit 8
Southborough, MA 01772-1033
+1-508-229-2000, Ext. 210
North America & Asia Technical Contact:
Device Technologies, Inc.
+1-508-229-2000, Ext. 250
DTi device technologies GmbH
Office: +49 40 350 85 128
Mobile: +49 177 170 3181
About Lockheed Martin Ventures
As a leading technology and innovation company, Lockheed Martin is committed to the next big idea. The mission of Lockheed Martin Ventures is to make strategic investments in companies that are developing disruptive, cutting edge technologies in core businesses and new markets important to Lockheed Martin. Since 2007, we have invested more than $100 million in startup companies. These emerging innovations have the potential to become foundational technologies that solve the complex challenges our customers face.